ETH002 Ethernet Relay
Devantech
Overview
The ETH002 provides two volt free contact relay outputs with a current rating of up to 16Amp each. The module is power from a 12vdc supply which can be regulated or unregulated. The DC input jack is 2.1mm with positive core polarity, DC supplies are required to supply at least 500mA at 12vdc. The relays are SPCO (Single Pole Change Over) types. The normally open, normally closed and common pins are all available on the screw terminals. The ETH002 has additional features over the ETH-RLY02:
- Full Factory Reset, all ETH002 firmware and settings can be reset to the original state.
- Firmware updates, firmware in the ETH002 is fully updateable by re-flashing the board with our custom windows program. This will be made available in the event of feature updates.
- New Command Format, the new command format allows for consistent compatibility with future boards. New commands now allow for pulsed control of relays from 100mS to 25.5 seconds.
- TCP/IP Password Protection, it is now possible to set a password for TCP/IP protection. This is independent of the configuration password.
Operating Temperature
-40°C to +70°C
LED indication
The ETH002 provides a red LED mounted immediately next to each relay to indicate whether it is in a powered state (LED on), there is also two LED's mounted in the Ethernet connector which will flash with Ethernet traffic. Finally there is a red power LED alongside the screw terminals.
Relay power rating
If the contact load voltage and current of the relay are in the region enclosed by the solid and dotted lines in the figure below, the relay can perform stable switching operation. If the relay is used at a voltage or current exceeding this region, the life of the contacts may be significantly shortened.
| load type | Typical applications | Rating | Max DC load capacity
|
| AC1 | Non inductive or slightly inductive loads |
16A @ 250V AC | |
| AC15 | Control of electromagnetic load (>72VA) |
3A @ 120V AC 1.5A @ 240V AC |
|
| AC3 | Control of motor | 750W | |
| DC1 | Non inductive or slightly inductive loads |
16A @ 24V DC | |
| DC13 | Control of electromagnetic loads |
0.22A @ 120V DC 0.1A @ 250V DC |
Download
A full datasheet for the relays used on the ETH002 is here.
Control
The relay board communicates via TCP/IP and is controlled with a set of commands, which are sent to the board's IP-address on a configurable port. The commands are sequences of bytes, for example:
The sequence 0x20, 0x01, 0x32 will turn on relay number 1 for 5 seconds. A full specification can be found at the manufacturer's spec (see link below).
Newer firmware versions allow control via ASCII-commands and also a long requested feature of control via http. For example: Sending a http GET to
192.168.0.200/io.cgi?DOA1=10
sets relay 1 on active for 1 second (This would use the default address 192.168.0.200). You can test these functions by typing them directly into the address bar of most internet browsers.
Also be aware that you may need to disable http authentication in the http configuration if your control device does not support it.
A full specification and firmware updates can be found at the manufacturer's spec (see link 'Technical Specification' below).
Mapped inputs
Digital inputs of the ETH484, ETH484-B, ETH044, ETH8020 or WIFI484 are able to be configured to remotely control outputs on all of Devantech's new ethernet relay boards (both wired and WIFI), the older ETH-RLY02 and ETH-RLY16 are not compatible however. The mapped inputs offer simple linking and versatile usage, an input in one country can control a output in another, or across a small network.
Possible target boards are:
The independent inputs can be mapped to different relays (on the same or different boards). In the "Address of target board", you can enter an IP address or hostname (which will be converted to an IP address by the DNS server supplied in the board configuration). If the module is on the local network then you can use the assigned IP address, if the target is over the internet then you need to supply the gateway in the configuration (internet source IP like your router) and the "Address of target board" is the IP address of the targets internet connection (to point at the router).
Board dimensions
YouTube Video
Setting up the larger ETH008 is explained in thie video.
IO Network - Android and iPhone App
Devantech created the free app 'IO network', available for Android and iPhone to remotely control your relays. Download it from Google Play or iTunes. Search for "Devantech" and you will find the app.
IO Network documentation for Android
IO Network documentation for iOS
Manufacturer's data
Accessories
plus EUR 5.95 shipping costs
Prices incl. VATEUR 15.11
plus EUR 5.00 shipping costs
Prices excl. VAT
Article no.: DEV-PA122521
More details...
plus EUR 5.95 shipping costs
Prices incl. VATEUR 18.47
plus EUR 5.00 shipping costs
Prices excl. VAT
Article no.: DEV-ETH002C
More details...
Product information for: ETH002 - Ethernet Relais Modul
Publishing date (date of last technical specification): 2013-11-01
Length: 85 mm
Width: 65 mm
Height: 21 mm
Weight: 80 g
Shipping weight: 150 g
Manufacturer: Devantech
Brand: ROBOT ELECTRONICS
Article number: DEV-ETH002
Manufacturer's part number: ETH002
The article ETH002 - Ethernet Relais Modul is listed in the following categories:
Modules > Relay > Ethernet
plus EUR 5.95 shipping costs
Prices incl. VATEUR 84.86
plus EUR 5.00 shipping costs
Prices excl. VAT
Article no.: DEV-DS378
More details...
dScript2824 - 24 x 16A ethernet relay without snubbers
without snubbers (Variations available)from ROBOT ELECTRONICS
Newest specification: 09/2016
plus EUR 5.95 shipping costs
Prices incl. VATEUR 142.00
plus EUR 5.00 shipping costs
Prices excl. VAT
Article no.: DEV-DS2824
More details...
plus EUR 5.95 shipping costs
Prices incl. VATEUR 47.88
plus EUR 5.00 shipping costs
Prices excl. VAT
Article no.: DEV-ETH002
More details...
plus EUR 5.95 shipping costs
Prices incl. VATEUR 142.00
plus EUR 5.00 shipping costs
Prices excl. VAT
Article no.: DEV-ETH8020
More details...
plus EUR 5.95 shipping costs
Prices incl. VATEUR 52.08
plus EUR 5.00 shipping costs
Prices excl. VAT
Article no.: DEV-DS1242
More details...
plus EUR 5.95 shipping costs
Prices incl. VATEUR 72.25
plus EUR 5.00 shipping costs
Prices excl. VAT
Article no.: DEV-DS3484
More details...
plus EUR 5.95 shipping costs
Prices incl. VATEUR 52.92
plus EUR 5.00 shipping costs
Prices excl. VAT
Article no.: DEV-ETH002-B
More details...
plus EUR 5.95 shipping costs
Prices incl. VATEUR 74.77
plus EUR 5.00 shipping costs
Prices excl. VAT
Article no.: DEV-ETH008-B
More details...
plus EUR 5.95 shipping costs
Prices incl. VATEUR 99.98
plus EUR 5.00 shipping costs
Prices excl. VAT
Article no.: DEV-ETH044
More details...
ETH0621 - 24v Motor controller and ethernet relay module
from ROBOT ELECTRONICSNewest specification: 02/2015
plus EUR 5.95 shipping costs
Prices incl. VATEUR 73.93
plus EUR 5.00 shipping costs
Prices excl. VAT
Article no.: DEV-ETH0621
More details...
Contact us
Order online now
Availability
Not in stock. We will obtain the article for you.
Estimated manufacturer's time of delivery: 30 days
updated: 17/11/2023
Information on currency
EUR 56.98 = GBP 48.72
EUR 47.88 = GBP 40.94
(€1=GBP0.85505)
EUR 56.98 = USD 65.23
EUR 47.88 = USD 54.81
(€1=USD1.1448)
EUR 56.98 = CAD 82.14
EUR 47.88 = CAD 69.02
(€1=CAD1.4416)
EUR 56.98 = AUD 89.40
EUR 47.88 = AUD 75.12
(€1=AUD1.5690)
Share
About ROBOT ELECTRONICS
ROBOT ELECTRONICS is a brand by English manufacturer Devantech Ltd., based in Norfolk. Product range comprises sensors, in particular ultrasonic or compass, servocontrollers as well as small robot drive systems or relay modules with various interfaces. Sensors are produced in England and are of consistently high quality.
More from ROBOT ELECTRONICS
